Know-It-All Snarky Tag

It's Tuesday which is my day to share a project created for Topflight Stamps. My Katzelkraft stamps were feeling neglected and I'm in a somewhat snarky mood due to exposure to a know-it-all, so I decided to make a tag featuring one of the fabulous critters from the the All Mad Here Unmounted Red Rubber Stamp Set along with a sentiment from the Whatchamacallit Unmounted Red Rubber Stamp Set by Katzelkraft.

Here it is!

Topflight Stamps Products Used:

All Mad Here Unmounted Red Rubber Stamp Set by Katzelkraft

Whatchamacallit Unmounted Red Rubber Stamp Set by Katzelkraft

Della Blue and Dark Denim Elements Inks by Lavinia Stamps

Medieval Blue VersaFine Clair Inks by Imagine Crafts/Tsukineko

Other Products Used:
Solar White Classic Crest Cardstock by Neenah Papers

Stonewash and Typhoon Cardstock by Bazzill Basics

Tuxedo Black Memento Ink by Imagine Crafts/Tsukineko

Copic Markers: E30, E31, E33, E34, E37, E47, E81, NV000, BV)0, BV20, R01, R11, YR21,  YR30, YR YR31, FY1, B91, B93, C10

Inner Peace Slimline Baroque Stencil by Jenine's Mindful Designs for Studio Light

White Gelly Roll Gel Pen by Sakura of America

Twine by American Crafts

Circle PaperShaper Punch by EK Success

Duo Corner Ticket/Tag Punch by Tonic

Repositionable Label Paper by Avery

STAY-tion by Wendy Vecchi for Ranger Ink

Stamping Platform

Instructions:

1. Use a stamping platform and Tuxedo Black Memento ink to stamp the hatted critter from the All Mad Here Unmounted Red Rubber Stamp Set two times, once onto a white cardstock panel and once onto repositionable label paper. 
2. Fussy-cut the label paper version  and place it atop its counterpart as a mask. 
3. Use magnets to secure the image panel to the STAY-tion.
4. Place a piece of plastic horizontally across the bottom of the image panel to block off the bottom part and secure the plastic with a magnet.
5. Brush Della Blue Elements Ink over the masked image. 
6. Place the Baroque Slimline Stencil over the image panel and secure with magnets. 
7. Brush Della Blue Elements Ink over the stencil to create a tone-on-tone pattern.
8. Move the plastic so that it's covering the top part of the image panel. Secure it with magnets.
9. Lightly brush Dark Denim Elements Ink over the bottom part of the image panel.
10. Lift the mask from the critter and retain for a later use.
11. Use Copic markers to color the image.
12. Touch up the critter's eyes with a C10 marker.
13. Use white gel pen to add catchlights to the critter's pupils.
14. Place the image panel back onto the stamping platform and secure with magnets.
15. Position the chosen sentiment  from the Whatchamacallit Unmounted Red Rubber Stamp Set facedown on the image panel above the critter, press the platform's lid onto the back of the stamp, and lift.
16. Ink the stamp with Medieval Blue VersaFine Clair Ink and stamp the sentiment onto the image panel. Re-ink and stamp again if necessary.
17. Trim the image panel and edge itwith Dark Denim Elements Ink
18. Cut Typhoon cardstock .25" larger than the image panel and use to mat it.
19. Cut a piece of light blue cardstock for the tag.
20. Use the duo--tag punch to trim the top corners.
21. Use a circle punch was used to cut a hole in the top part of the tag.
22. Edge the tag with Dark Denim Elements Ink.
23. Adhere the matted image panel to the tag. 
24. Thread strands of twine through the hole to finish the tag.

Thanks for visiting today.

I shall enter this tag into the following challenge(s).

• Sisterhood of Snarky Stampers: C is for Critters